XC Engineering Srl

  • Home
  • Company
    • Expertise
    • History
    • Partners
  • Services
    • Consultancy
    • Reselling
      • FLOW-3D
      • FLOW-3D Cast
      • IMPROVEit
      • Support and trainings
    • Software development
  • Industries
    • Aerospace
    • Automotive
    • Biotechnologies
    • Coastal & Maritime
    • Ship Design
    • Water & Environmental
    • Casting
    • Coating
    • Energy
    • Manufacturing
    • Microfluidics
  • Contact us
    • Job opportunities
    • Thesis/Stage
  • English
    • English English
    • Italiano Italiano
    • Français Français
You are here: Home / Archives for sand molded casting

19/06/2019 by Raul Pirovano

Design optimization for mass production

Introduction The development of a product involves various phases of calculation and design that provide a series of predefined steps to follow in order to reach mass production. With this aim in mind and considering the high number of parts to be produced, any material saving is advantageous and relevant from an economic perspective. The parties involved in the production need to reduce the waste material (relevant for the foundry) and to reduce the weight of the components (relevant for the end customer). Optimizing the shape of the product helps both parties (foundry and customer) to reach the right compromise to make the adequate savings while obtaining the highest quality parts. In this article we will show the design optimization process of a foundry product destined for mass production using an optimization software and a process simulator. The aim is to analyze the solidification of the metal present in the system of interest and to evaluate how the optimization helps both parties to benefit from it. Component to produce The component to optimize in this study is produced by sand molded casting technique, one of the oldest, simplest and most economical techniques. The preliminary design phase has provided a prototype in stereolithography format (STL), which is already potentially good for production (courtesy of Flow Science Deutschland). In the image [Figure 1] you can see the feeding system (in yellow) and the geometry of the part to be produced (in red). The weight of the part itself in this starting configuration is 2,197kg, and the whole system weight is 3,126kg. The main objective is, by acting on some details of the geometries themselves, to obtain a total weight of the system as small as possible without having significant porosity in the part. In order to obtain the best possible result, the parameters chosen to be modified are the size of the feeder [Figure 2], the thickness of the vertical wall closest to the feeder and the thickness of the transition zone between the two walls [Figure 3]. Figure 2 - First optimization parameter Figure 3 - Second and third optimization parameters The considered variables are thus potentially multiple and exploring manually all the possible combinations can be a very long and complex work. That is why we have chosen to use a numerical optimizer able to explore the solutions independently. Therefore, IMPROVEit was chosen, which thanks to its simple interface allows to perform both the setup phase and the processing of results easily. FLOW-3D® CAST was chosen as the process simulator for its precision, reliability and simple use in foundry simulations. As for modifying the geometrical shape, the optimization software allows both to interact directly with parametric CAD if the file is in original format, and to modify an STL file directly inside IMPROVEit if, as it is the case in this test, only the latter is available. Once the parameters to be corrected have been selected, the software is able to internally modify the shape of the geometries, launch the solidification simulations interacting with the FLOW-3D® CAST process software using the modified geometries, extract the results of the analyses and process them with suitable mathematical nodes to obtain the right optimized quantity. [Figure 4] shows the workflow of our case study. Figure 4 - Optimization workflow In order to detect the shrinkage porosity dimension present at the end of the solidification simulation, four control volumes divide the geometry in four distinct zones: the top part is in dark blue, the central part in yellow, the left part in cyan and the right part in magenta. According to the customers’ exigences, among those four parts only three are relevant for optimization: the porosity in the top part (dark blue) is not considered. In the initial configuration, the total shrinkage porosity volume in the three control volumes is 581mm3. Figure 5 - Control volumes Execution For the purpose of the optimization process, two objectives and one constraint were chosen: minimizing the feeding system and the part’s weight while having the amount of porosity in the three control volumes below a threshold low enough to be able to consider the part free from visible defects. Setting up an optimization with two objectives and a constraint makes the understanding of the problem complex; nevertheless, the IMPROVEit engine being developed specifically for this type of problem, it allows to obtain an excellent result with just a few calls of the process simulator. Since each optimization cycle lasts only a few minutes, it was decided to allow the execution of fifty cycles. Considerations After fifty cycles, IMPROVEit was able to propose a wide range of solutions that reduce the weight of the system with tolerable thresholds of porosity, which was our objective. Moreover, by analyzing the panorama of the solutions found, it is possible to … [Read more...]

Filed Under: Casting, Optimization Tagged With: casting, cfd, FLOW-3D Cast, IMPROVEit, optimization, sand molded casting

Recent Posts

  • FLOW-3D CAST v5.1 Released
  • Simulation and optimization to minimize foundry defects
  • Vertical Spike Wave
  • Design optimization for mass production
  • Increasing Discharge Capacity with the Piano Key Weir

XC Engineering SRL

via Matteotti 7, 22063
Cantù (CO) - ITALY
Tel.Fax: (+39) 031 715 999

  • English (en)English
  • Italiano (it)Italiano
  • Français (fr)Français

Tags

additive manufactory casting cfd dam Discharge energy fabbrication additive fabbricazione additiva FLOW-3D FLOW-3D Cast Fluid Dynamics foundry HPDC hydraulic hydraulics IMPROVEit laser LPDC Numerical optimization ottimizzazione Pelton Piano Key Weir powerplant river saldatura sand molded casting simulation spike wave toilet transient turbine vertical spike wave water wave welding

XC in social media

  • Facebook
  • Google+
  • LinkedIn
  • YouTube
Home | Company Data | Terms & Conditions | Privacy Policy |
This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Cookie settingsACCEPTDECLINE
Privacy & Cookies Policy

Privacy Overview

This website uses cookies to improve your experience while you navigate through the website. Out of these cookies, the cookies that are categorized as necessary are stored on your browser as they are as essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may have an effect on your browsing experience.
Necessary
Always Enabled
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
SAVE & ACCEPT